Linear Bushings (LM..MGLM Guide
| 호칭 (원통형) | 내접원경 | 외경 (øD) | 길이 (L) | B | W | D1 | |||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| 기준 | 精 | 上 | 기준 | 精·上 | 기준 | 허용차 | 기준 | 허용차 | |||
| LM3M-UU | 3 | 0 -0.005 | 0 -0.008 | 7 | 0 -0.009 | 10 | 0 -0.12 | - | - | - | - |
| LM4M-UU | 4 | 0 -0.005 | 0 -0.008 | 8 | 0 -0.009 | 12 | 0 -0.12 | - | - | - | - |
| LM5M-UU | 5 | 0 -0.005 | 0 -0.008 | 10 | 0 -0.009 | 15 | 0 -0.12 | 10.2 | 0 -0.2 | 1.1 | 9.6 |
| LM6MG-UU | 6 | 0 -0.006 | 0 -0.009 | 12 | 0 -0.011 | 19 | 0 -0.2 | 13.5 | 0 -0.2 | 1.1 | 11.5 |
| LM8SMG-UU | 8 | 0 -0.006 | 0 -0.009 | 15 | 0 -0.011 | 17 | 0 -0.2 | 11.5 | 0 -0.2 | 1.1 | 14.3 |
| LM8MG-UU | 8 | 0 -0.006 | 0 -0.009 | 15 | 0 -0.011 | 24 | 0 -0.2 | 17.5 | 0 -0.2 | 1.1 | 14.3 |
| LM10MG-UU | 10 | 0 -0.006 | 0 -0.009 | 19 | 0 -0.013 | 29 | 0 -0.2 | 22 | 0 -0.2 | 1.3 | 18 |
| LM12MG-UU | 12 | 0 -0.006 | 0 -0.009 | 21 | 0 -0.013 | 30 | 0 -0.2 | 23 | 0 -0.2 | 1.3 | 20 |
| LM13MG-UU | 13 | 0 -0.006 | 0 -0.009 | 23 | 0 -0.013 | 32 | 0 -0.2 | 23 | 0 -0.2 | 1.3 | 22 |
| LM16MG-UU | 16 | 0 -0.006 | 0 -0.009 | 28 | 0 -0.013 | 37 | 0 -0.2 | 26.5 | 0 -0.2 | 1.6 | 27 |
| LM20MG-UU | 20 | 0 -0.007 | 0 -0.010 | 32 | 0 -0.016 | 42 | 0 -0.2 | 30.5 | 0 -0.2 | 1.6 | 30.5 |
| LM25MG-UU | 25 | 0 -0.007 | 0 -0.010 | 40 | 0 -0.016 | 59 | 0 -0.3 | 41 | 0 -0.3 | 1.85 | 38 |
| LM30MG-UU | 30 | 0 -0.007 | 0 -0.010 | 45 | 0 -0.016 | 64 | 0 -0.3 | 44.5 | 0 -0.3 | 1.85 | 43 |
| LM35MG-UU | 35 | 0 -0.008 | 0 -0.012 | 52 | 0 -0.019 | 70 | 0 -0.3 | 49.5 | 0 -0.3 | 2.1 | 49 |
| LM40MG-UU | 40 | 0 -0.008 | 0 -0.012 | 60 | 0 -0.019 | 80 | 0 -0.3 | 60.5 | 0 -0.3 | 2.1 | 57 |
- Note.
- 공작기계용으로는 양측 Seal Type을 사용바랍니다.
- 권장 하우징 내경공차는 다음과 같습니다.
상급(H) : H7/J7 , 정밀급(P) : H6/J6